Power IMIG205 Pulse info

[Oxide00]

Any more info on the the new IMIG 205p that I have heard about?

[performance]

Oxide,
We have been selling them. They are here.

[Wrenchtamer]

Man, that's awesome. Is there any way one could procure an image of said welder? Nevermind I found it. I'm really kicking myself right now. But the regular 205 is still a great machine.

[performance]

There are updates coming to the units. But if you asked me which I would rather use, it would be the non pulse unit. The AWS seems to think so as well, and it is my understanding, they don't regard it as a valid process for welding procedures in MIG. Price is significantly more as well.

[everlastsupport]

I use a 250P for most of my MIG welding and I never use the pulse controls. Never had a reason and never been disappointed in a weld it's done. I wish the 250P went lower than 40amps as that's a tad to hot for sheet metal.

The 205P would be a good choice for those doing sheet metal to 1/4"-3/8" steel (single pass) but still want the pulse mode. Not a bad range.

If you have the extra cash, nothing wrong with the 205P. But I agree with Mark, I too would probably skip the pulse unless I could not get the unit I wanted without it.

[Oxide00]

Are you guys planning to put up any demonstration videos for your MIG welders.

[dlcain]

Could you tell me what settings you use for non-pulse operation? Been playing around with the welding machine for almost a year now and still unsure of what settings to use...


Thanks,
-don

I use a 250P for most of my MIG welding and I never use the pulse controls. Never had a reason and never been disappointed in a weld it's done. I wish the 250P went lower than 40amps as that's a tad to hot for sheet metal.

The 205P would be a good choice for those doing sheet metal to 1/4"-3/8" steel (single pass) but still want the pulse mode. Not a bad range.

If you have the extra cash, nothing wrong with the 205P. But I agree with Mark, I too would probably skip the pulse unless I could not get the unit I wanted without it.

[srp]

I use a 250P for most of my MIG welding and I never use the pulse controls. Never had a reason and never been disappointed in a weld it's done. I wish the 250P went lower than 40amps as that's a tad to hot for sheet metal.

The 205P would be a good choice for those doing sheet metal to 1/4"-3/8" steel (single pass) but still want the pulse mode. Not a bad range.

If you have the extra cash, nothing wrong with the 205P. But I agree with Mark, I too would probably skip the pulse unless I could not get the unit I wanted without it.

Lorch and Fronius both have dual or twin pulse, a slow pulse at .2 (1 pulse every 5 seconds) and a fast pulse up to like 2000 pps. Both will put down tig like welds without any gun manipulation, Fronius's will be made in USA in October. I am looking at the Lorch and may get one. Check out the video on you tube by Lorch (masters of speed).

http://www.youtube.com/watch?v=9xhbC9saI14

[everlastsupport]

Could you tell me what settings you use for non-pulse operation? Been playing around with the welding machine for almost a year now and still unsure of what settings to use...
Thanks,
-don

Don,

Not sure what machine you have. Assuming it's a MIG since you quoted a MIG post.. Here is a link to help with the welder for the 205 from a member that is pretty close to what I use. But it will give you the mind set to match up the voltage for your style as well.

http://www.everlastgenerators.com/fo...28by-Geezer%29

With the pulse off I would figure you get about 14-24V range or better. Best to make notes when you test it on different thickness metals. We honestly look at the metal, set it, tweak if needed and go.

[srp]

Every pulse mig I have welded with will adjust out to have less sparks and splatter, that is why I want a fast pulse. The slow pulse at .5 pps or slower makes a beginner look like a professional tig welder. The problem is they cost about 8000 bucks.

Everlast needs to add slow pulse (dual pulse) to they 205P and 250P, I would buy the first one.

http://www.youtube.com/watch?v=JWWMwrit7hs