Anyone else have problems with this board loading new pages REALLY slow or not at all at times? Sometimes I just get page not found.
Member
Slow at times?
Anyone else have problems with this board loading new pages REALLY slow or not at all at times? Sometimes I just get page not found.
Gerald
Millermatic 251
Spectrum 300 Plasma
Everlast PowerTig 250EX
Everlast PowerCool W300
Harris / Victor OA
Craftsman 13 Speed Drill Press
ProTools Air/Hydraulic Bender
48" Brake, 72" Brake, 52" Stomp Shear
Mitler Bros. 36" High Throat Bead Roller
Compressor, Notchers, Grinders, etc.
Senior Member
I have seen the same thing. It appears to be a bandwidth thing as I was up in the middle of the night with my daughter (sick) and it was very fast. Busy times seem to take a toll. Sometimes the pages will load given enough time, and other times, it gives the same page not found.
Everlast 200DX
Everlast PT185
Shoptask 3-in-1 (not currently in my garage, but I own it...)
Any day on a motorcycle like this that ends just needing parts and labor is a good day.
4.82, 158.67mph 1/8th mile 7.350, 200.35mph 1/4 mile
Member
It doesn't seem to matter for me what time of the day or night it is, or how many are on the board at the time. Its more of a random thing. Its fast right now. Was really slow before I started this thread. Its been this way for me even before the board upgrades.
Gerald
Millermatic 251
Spectrum 300 Plasma
Everlast PowerTig 250EX
Everlast PowerCool W300
Harris / Victor OA
Craftsman 13 Speed Drill Press
ProTools Air/Hydraulic Bender
48" Brake, 72" Brake, 52" Stomp Shear
Mitler Bros. 36" High Throat Bead Roller
Compressor, Notchers, Grinders, etc.
Member
I just got knocked off entirely, dead 'no connect page' page came up. I checked my speed [above] and it wasn't on my end. It was down maybe 2 minutes. No big deal, it was a first for me. Just posted for educational reasons.
I am out trying to 'find myself'. If I should wander back while I am gone, please tell me to sit quietly and wait for myself to return.
LOTS of scuba and vintage scuba equipment [I'm Always willing to trade or buy the stuff you think is too old to use]
Smithy XLT Mill/lathe [It was easier to learn than I thought, I'm no pro, but I can make a bearing hanger]
Everlast PP256
Everlast Sales and Support Team
We hitting the server hard, I feel your pain, hang in there.
____
Ray
Everlast Sales and Support Team.
support@everlastalaska.com
www.everlastalaska.com
877-755-9353 X207
Member
its been hit or miss for me, but today I have been getting a lot of 500 and 503 errors
sold my miller mig
got a PT250EX
saving up for a plasma cutter
Member
Only two members and 13 guests on here right now, and it took me 12 min. to post this.
PS. And a WHOLE LOT of spam posts. Even seen one new member with one post, welcoming another member to the board who is a regular poster, that has been here for 6 months already.
Last edited by Rugar; 03-07-2011 at 09:03 PM.
Gerald
Millermatic 251
Spectrum 300 Plasma
Everlast PowerTig 250EX
Everlast PowerCool W300
Harris / Victor OA
Craftsman 13 Speed Drill Press
ProTools Air/Hydraulic Bender
48" Brake, 72" Brake, 52" Stomp Shear
Mitler Bros. 36" High Throat Bead Roller
Compressor, Notchers, Grinders, etc.
Senior Member
I also have been seeing the forum running slow. I have not seen it as bad as some of you. The worst I get it is taking about 30 seconds to load a page. I think one time it timed out but then was back to just a slow load right after.
Jason
Everlast 255EXT - Perfection
Everlast PowerPro 256 - UPS Demolished
Everlast MTS200s
12 Ton Shop Press
DeWalt Hand Tools/ChopSaw
Member
yea, been getting alot of hangups lately, its odd, one click will run right thru, and open up almost imediately, the next you get a hangup.
its a bit frustrating at times.
300whp FWD 94 Celica
PowerPro 205 with a hack behind the mask!
Member
Same with me. Sometimes lightning fast other times "page not found". It can be frustrating when you've just typed three paragraphs and they all got dumped when you try to refresh. LOL
PowerTig 225LX
PowerCool W300
PowerPlasma 60S
Miller 140 MIG
New Member
most of the time i get on here it's slower then molasses but some days it just doesn't move at all ends up telling me my session timed out
everlast i-mig 200
96 gmc extended cab truck 350 rwhp daily driven for 289,000 miles
88 jeep cherokee custom built by me for me for well everything.someday it'll be finished
4.6L stroker,dana 44 front, 14 bolt rear, 35"xterrains,soon to come 231/205 doubler
Member
Ooh, and I pay $46.97 per month to be slower than 66% of America....LAME!!
I Love Plasma and rolleye's at the costly addiction of MAPPgasoron's.
http://brothers2woodworking.webstarts.com/
Everlast Plasma cutter Power Plasma 50
Everlast PowerArc 200 ~ Happily Married To That gutsy babe, git'er dun.
Wishlist: Free consumables, Small TIG maybeAlex, when you have overstock give me ring!
Member
I pay $40/month for 1.5meg down and 256 up and average about 300K down. Yours speed looks mighty fine to me.
Thurmond
Miller Bobcat 3 Phase,
Miller Suitcase X-Treme 12VS wire feeder for the Bobcat with M-25 300A .045" gun / Bernard 400A 5/64" wire mig gun .
26 series gas cooled TIG torch, setup for quick connect to Bobcat.
17 series gas cooled Tig Torch for Low Amp Solar Tig (Direct Solar Panel Powered Tig welding)
Hobart Handler 187 Mig / Fluxcore
EVERLAST PowerUltra 205P
EVERLAST PowerTig 250 EXT 2013 Model
Posting Permissions
Reply With Quote
