The UPDATED line of welders and then some...

[performance]

I promised a new reveal soon....Here is our new Power I MIG 250 P. Yes, folks that's right, state of the art pulse Mig technology with 250 amps. Its roll around as you can see. It will hold a full size bottle of Argon and a full 40 lb roll of wire. It uses a name brand Mig Gun, known for its ergonomic feel. It also has burn back, and arc force control to round out the pulse features.

Also posted is the all new (previously mentioned) PowerARC 200. It is a full 200 amp DC welder with Hot start technology and automatic arc force control. It also has a special "6010" hole for those of you welders that know what one is.
Its extremely compact, but is perfect for about any onsite job repair or fabrication. It is designed to run with generators, as long as the power is fairly clean, so that it makes about any field repair a snap.

Also, we are revealing the PowerMaster 256 for the first time...which nearly mirrors the 250 EX in features and performance, although you do sacrifice the lift start capability for the additional feature of the plasma cutter. Also not included is the spot timer function....We had to have a little room for the plasma circuit, but it is as near as we can get to the EX with a 60 amp plasma built in.

If you think that all we have to introduce, then you are wrong. We still have at least two or possibly 3 more things in the works that you will have to wait another week to find out.

[performance]

Couldn't wait...here's one more....
(Don't worry, we still have a couple of nice suprises)

The Power I-MIG 160:

It is a nice little MIG/Stick machine...That's right, it features MIG and Stick capability. Again, it features a genuine name brand Mig Gun. It is very compact and will still hold a 11-12 lb spool of wire. By special order, you can get special Flux core drive rolls. It has a 135 amp rated performance at 35% duty cycle with a 60 % duty at 100 amps...more than enough for the typical home or pro garage fabrication or repair. It also has a spool gun port to provide the special "aluminum" capability that so many think can only be done with Tig. The spool gun can carry a wide range of wires, including stainless so that it makes welding expensive metals more economical and convenient.

[acourtjester]

HI
Now tell me what is the big difference between the PM-226 and PM-256 since the spot timer function and lift start was droped??

I have a PM-256 on order can you tell me when they will be shipped??

Have fun
Tom

[performance]

They will begin to be shipped as soon as they come in. They are on the water and have been about a week and will be here soon.

The 226 lacked several of the features of the new 256.

Now the 256 has all of the current and timer presets of the EX, including identical pulse, and frequency ranges. The 256, since it is a combination machine is not targeted to the typical consumer that would use it in conjunction with a spot welder, so it was left off. Also the Lift start feature was not considered to be a absolutely necessary feature since it is in a select few areas that a lift start is needed, and space inside the machine is limited.

[acourtjester]

I guess the new web page got it's 15 seconds of fame and is gone now!!!

[BurningMetal]

when will the new website be up? .........with the new machine and specs.

I check ever day......can you tell I am itching to buy a Tig? :-)

[everlastsupport]

It is coming, I told Oleg it was up for a bit and he did not believe me.

BurningMetal, the new units are in. I can send you specs on whatever line you are looking for. We have them in jpgs, just not on the website yet.

Sorry for the delays, we are moving as fast as we can. I know the Ca. office is swamped.

[BurningMetal]

Mike,

I am still undecided whether to go all-in-one or just get the Tig for now.

Can you send me the sheets for the 200DX, 225LX, and the 250EX?

Also, I don't know the all-in-one models, but can you send me the specs on the 200AMP and the 250AMP all-in-ones?

thanks,

Andrew

[everlastsupport]

Here you go. If not big enough, shoot an email and I will attach them.