PowerArc 160 STH Almost ready

[Titan winch]

Attachment 5142

Tomorrow Morning i start testing the first Production run of the new PowerArc 160 STH . Stick HF and Lift Tig
Here is a early picture of units not quite ready for testing.

[EchoSixMike]

Attachment not working. S/F....Ken M

[Titan winch]

Try this and see if it works. The Internet and our site seem to have issues over here

[Ray]

Try this and see if it works. The Internet and our site seem to have issues over here

HI Duncan,
Oh, now I know why I find the small brown string stuck under the control knobs on occasion. LOL.
You look like you’re staying busy!

[charger891]

your back at the plant again? your a busy guy!!

[Oleg]

your back at the plant again? your a busy guy!!

charger89

Yes Duncan is there for next few weeks. 160 unit looks GOOD !!!
Mark did good on front panel !

[EchoSixMike]

So the unit I purchased last week, marked TIG 160, and which I tested today(works fine is a prototype or preproduction model or something? S/F....Ken M

[Oleg]

So the unit I purchased last week, marked TIG 160, and which I tested today(works fine is a prototype or preproduction model or something? S/F....Ken M

Ken , unit you have is SAME as being in production now. We only changed the case and panel. Inside is 100% same

[EchoSixMike]

Sounds good, thanks for the reply. My limited playing with the unit has gone well. Portability seems good. A little more compartmentalization in the case would have been good for a portable unit like this. Perhaps offering an aftermarket Pelican or Stormcase type container for those of us who will be using it in a maintainance application around animalistic coworkers? Both TIG and stick function is OK. Very happily surprised by the adjustable post flow, was not expecting that. Would like some form of down slope, as there does not appear to be any at present, and dropping from high amperage to zilch is not optimal. Very happy with the stick electrode holder and ground clamp, but in the near future I'll probably be adopting a compact torch and foot pedal simply due to preference. I supose I should call about options for foot pedal? S/F....Ken M

[Titan winch]

The cards are using for accountability for each work process and also to record any issues during calibration and scope readings. It stays with the machine till the final stage of testing then it is removed when unit is packaged.

[jerky]

Stick HF and Lift Tig

um, im going to assume there was supposed to be a comma between stick and HF yes? took me a minute to process that.

[charger891]

Thanks Duncan for posting pictures like this from the factory, it shows you guys are putting serious efforts into this brand, not like some other knock off brands i dealt with in the past. May i suggest something, you guy`s should have these pictures on your website, it shows that you guys are constantly testing and improving your products, people that are corious of this brand but have doubts, this might swing them into a sale??

[Titan winch]

Thanks Duncan for posting pictures like this from the factory, it shows you guys are putting serious efforts into this brand, not like some other knock off brands i dealt with in the past. May i suggest something, you guy`s should have these pictures on your website, it shows that you guys are constantly testing and improving your products, people that are corious of this brand but have doubts, this might swing them into a sale??

Well i try to put some serious effort into it except when Oleg calls ( second picture ) about 5 times a day normally , sometimes more .

[everlastsupport]

I think the 160STH is going to be a great seller. The 110volts and HF start. Compact and light weight but enough power for most jobs.

[Oleg]

Ian

Not sure where longivity buys there units but our units leaving factory next week

PowerArc 140st , 200 and 300 in stock

PowerArc new 160 will be in stock march 12th


Oleg Gladshteyn
Oleg@everlastwelders.com
415 613 664 cell
650 588 8588 work

[performance]

Ian,
If you look closely, those are extra covers for Everlast, and the shape of the triangle at the top is distinctive as being ours. Additionally, as we have published, we have forged an exclusivity agreement with the factory.

[everlastsupport]

I see some units in the upper left corner (red lined) and the covers on a rack to the right of them.

AND for sure, I see Duncan in that picture.

[SeanMurphy265]

Ian,
If you look closely, those are extra covers for Everlast, and the shape of the triangle at the top is distinctive as being ours. Additionally, as we have published, we have forged an exclusivity agreement with the factory.

Will their (China) laws protect a foreign company that has their manufacturing in China?