Rotenbach Super 200p

[everlastsupport]

Janne, please do not share them, you are not our customer (but we hope one day) and we went out of our way to help you out. Mark offered as a favor, I got them to you as you could not receive them due to size. They are for your eyes only.

Mark, good news, Jake's cool as you know. I actually was going to PM him and send them to him at some point. He and I have fixed his old 200P unit over the phone in the past.

But we do not want the upstarts to keep pumping stuff and trying to use our older stuff to help them. Our new stuff is awesome compared to the old product. We want to keep going that way.

[woody068]

Really sorry, didnt realize that it was confidential.
I will not share them from now on.
Jakeru helped me with some troubleshooting and i thought i would help hom back, sorry.

[Gazampher]

Hi Woody,

I was wondering if you made any progress with your broken Super-200p. From reading your posts I seem to have almost the same problem except I believe I may have made mine worse by not putting the unit back together correctly. Do you have any pictures to hand to help me put all the connectors back into the correct sockets please.
It is mainly the wires from the fron control board and the one mounting behind it.

Thanks

[zoama]

Hi Woody,

I was wondering if you made any progress with your broken Super-200p. From reading your posts I seem to have almost the same problem except I believe I may have made mine worse by not putting the unit back together correctly. Do you have any pictures to hand to help me put all the connectors back into the correct sockets please.
It is mainly the wires from the fron control board and the one mounting behind it.

Thanks

Be aware that the machine in this thread is not an Everlast and not the same build.

[Gazampher]

Mine too is not an everlast machine, it has LTS on the side which as far as I can work out is a UK importer of these machines. I have not had much luck with them as I was not the original buyer and it was purchased back in 2009. From the pictures mine appears to have the same electronics inside but I cannot work out exactly what connections go where.

I think with a bit of time and effort using my experiance in electronics I could reverse engineer the electronics and create some schematics for each of the boards used in the unit. I already have done the main power control PCB located at the bottom, the others will take some more time as they are a bit more complicated.

If anyone can help with the internal wiring I would be very greatful.

Cheers.

[miamijim]

How can I get some schematics for the front pot board of the super200p ?

I see some are available, my unit is a bit different in the layout of the ICs.

They are horizontal in layout not vertical like the one picture here..
There are 2 LM324's.

So if some one has pdf's of these boards of the different models, I sure could use it.

Thanks , I'm new to any foruming so please bare with me.
I hope I'm doing this right..

Is there a download service site, That needs a user and password , I could get ?

mmiamijim@gmail.com
thanks

[performance]

Unless you know the actual manufacturer of your unit, it's kind of useless to send out schematics. We have no way of knowing what boards you have, since probably over 200 manufacturers make a model similar to this...and with that there are as many variations.

[miamijim]

The mfg is simarc or simadre. Considered a 4in1 has plasma cutting to.
Thanks

[performance]

That's not the manufacturer. Someone made it for them...which could be several different ones.

[poxxxy]

Old post but I appear to be experiencing similar problems to Janne here... I took out the bottom PCB board to test some suspect diodes but they all checked out ok out of circuit. Part number on this board on my LTS UK super 200P is: HB19195, has 6 large brown caps on there.

I noticed that one on of the power connectors going up to the mid back left mosfet board, there is a cable which appears to be out of place... it looks as though it should have a female spade connector present as there is some heatshrink tubing and the other row of mosfets has this connection made in the location where the heatshrink tubing is...

Maybe this is a root cause of my problems!

I'd appreciate any schematics that might be available for the machine.

Maybe i'll get a HF spark someday .