OK, here is one of my big beefs with the Green Guys...

[Yofish]

I'm contemplating buying a i-mig 250P machine. So being somewhat interested in the specifics I hopefully (foolishly) go and try to find them by following the yellow brick road that 'normally' gets you to satisfaction, i.e. clicking on DOWNLOAD MANUAL. Wrongo Bongo! All one gets is something that has nothing to do with the machine you are interested in, BUT, you can find out the vague particulars of a machine that isn't offered any more. One can download the brochure, which has information but is hardly a manual. A MANUAL is a Manual is a MANUAL. What is so hard about this?

Yes, to those that have been around, I'm already aware that lugnutz will come back and tell me that the brochure 'is all that a REAL welder needs to know'.

[Rugar]

http://www.everlastgenerators.com/si...nloads/mig.pdf

[Rambozo]

http://www.everlastgenerators.com/si...nloads/mig.pdf

That is the way out of date manual that was mentioned. The US manuals are written here after the machines have shipped so they always lag behind. I guess if you can read Chinese, you might be able to get something more current.
Also the product cycle is a lot different than red or blue where they sell the same machine for a decade or more. Green tends to make ongoing changes. Usually the most current specs are posted to this forum, often before the machines are even shipped. An email or phone call will be the easiest way to get the current specs and have any questions answered.

[everlastsupport]

The machine, I personally have had two IMIG-205P over the years (still have one almost use daily; and the IMIG-200 non-pulse used more).

They will do about anything (the 250P), but they take a bit to figure them out (like the IMIG-205P as well).

I think Geezer wrote a IMIG-205P setup thread on here, years ago and it was good. I would a start there with a forum "search", or ask a question here, many people here can help you.

Insulting Mark is not fair if you do not know him, he's a hard working guy that makes a lot of those changes for our products. He even just told a guy they are for the more advanced, not sure why you did not see it if you're searching for a 250P questions. He's a great guy, always making us better, but sometime he can be direct.

Why not ask your questions? Many sharp guy on here, seems like they have no lives sometimes . Welder types normally have a thicker skin. Probably all the time I took off the gloves and did not allow enough time before grabbing it

I will see if I can find the setup from Geezer. Or I see him online sometimes, maybe he will update it or point to it. It might be a sticky even.

[performance]

If you want a specific manual for that unit, you'll need to take it up with someone else...I write the ones I am asked to write. I'd never tell anyone that a brochure is enough. That's asinine at best. The 250P, while still on the books, is out of stock now and our immediate plans for production are on special order only for now. The 250 outsells it by far and we're putting our efforts into fostering it's growth. Manual for it will be up in a few days.

[Yofish]

If you want a specific manual for that unit, you'll need to take it up with someone else...I write the ones I am asked to write. I'd never tell anyone that a brochure is enough. That's asinine at best. The 250P, while still on the books, is out of stock now and our immediate plans for production are on special order only for now. The 250 outsells it by far and we're putting our efforts into fostering it's growth. Manual for it will be up in a few days.

OK, thanks I guess that's the end of story then. I was looking to mate the Miller XR box to 250P because I want pulse for AL. If I'm seeing everything correctly and from what you say, that can't happen unless I was to special order the 250P? That doesn't sound attractive, especially if it needed service.